Our largest case in the range – designed for the largest specialist electronic devices including radio microphones and some medical devices such as nebulisers.
This video shows you how to use the TC clamp sealing system as used on all our cases which have cables or tubes coming out of them. Follow instructions carefully as there is a small trick - leave a gap between the sealing bars before closing the clamp levers.
Also works with pulmonary hypertension pumps.
This case is designed for electronics which require a thin wire to be connected to them at all times. The special wire-thru clamp at one end allows that wire to stay connected, and be waterproof. The case is usually used by professionals with specialist electronic devices, but could be used for a permanently connected small tablet, large phone or audio player.
Key Features
- Use all buttons and switches through the case
- Like most of our cases it'll float if you drop it in the drink
- Feed out a wire of up to 3.5mm diameter from the case
- The seams are high-frequency welded to form a super-strong bond
- Waterproofness Warning!: This case features our 'TC' Aquaclip which makes the case waterproof to IPX6 (a quick dunking should be fine, but not prolonged immersion).
Can people swim with it? Our testing shows that the TC clamp will let a tiny amount of water in after a period of total immersion. So the best advice we can give is to wear it in the small of your back if you’re swimming on your front, and on your tummy if you’re swimming on your back, so that it spends as little time submerged as possible. We are talking here about splashing around in the pool or the sea, but we are NOT talking about endurance/long-distance swimming.
Important Notes Cases with this clamp are for surface use only, but will offer protection from temporary submersion. They are not recommended for prolonged immersion. When not using the case leave the TC clamp open. If not the wire or tube could eventually cause a permanent distortion of the foam, risking leakage. As long as you follow this instruction the clamp will be watertight with or without a wire/tube. The maximum thickness of wire/tube around which the TC clamp will seal is 1/10th inch (3.5mm).
https://www.youtube.com/watch?v=Fky5j_8Aw-g
Made in UK
(code Q558 )
Large Medical Device Case
Waterproof Radio Microphone Case - Large
Our largest case in the range – designed for the largest specialist electronic devices including radio microphones and some medical devices such as nebulisers.
This video shows you how to use the TC clamp sealing system as used on all our cases which have cables or tubes coming out of them. Follow instructions carefully as there is a small trick - leave a gap between the sealing bars before closing the clamp levers.
Also works with pulmonary hypertension pumps.
This case is designed for electronics which require a thin wire to be connected to them at all times. The special wire-thru clamp at one end allows that wire to stay connected, and be waterproof. The case is usually used by professionals with specialist electronic devices, but could be used for a permanently connected small tablet, large phone or audio player.
Key Features
- Use all buttons and switches through the case
- Like most of our cases it'll float if you drop it in the drink
- Feed out a wire of up to 3.5mm diameter from the case
- The seams are high-frequency welded to form a super-strong bond
- Waterproofness Warning!: This case features our 'TC' Aquaclip which makes the case waterproof to IPX6 (a quick dunking should be fine, but not prolonged immersion).
Can people swim with it? Our testing shows that the TC clamp will let a tiny amount of water in after a period of total immersion. So the best advice we can give is to wear it in the small of your back if you’re swimming on your front, and on your tummy if you’re swimming on your back, so that it spends as little time submerged as possible. We are talking here about splashing around in the pool or the sea, but we are NOT talking about endurance/long-distance swimming.
Important Notes Cases with this clamp are for surface use only, but will offer protection from temporary submersion. They are not recommended for prolonged immersion. When not using the case leave the TC clamp open. If not the wire or tube could eventually cause a permanent distortion of the foam, risking leakage. As long as you follow this instruction the clamp will be watertight with or without a wire/tube. The maximum thickness of wire/tube around which the TC clamp will seal is 1/10th inch (3.5mm).
https://www.youtube.com/watch?v=Fky5j_8Aw-g
Made in UK
(code Q558 )
Quality Manufacturing
Aquapac have been making waterproof cases for 40 years in the UK. We are committed to maintaining the highest standards, We test each production run in our pressure tanks. We work with the best precision toolmakers to ensure top quality.
Committed to Sustainability
The majority of Aquapac cases are made from biodegradable and recyclable plastics. Our products are designed to be used thousands of times. We reduce our already minimal packaging each year and only used recycled board.
We have minimal waste and our machines are powered by
solar panels on our factory roof. Over 80% of our raw materials are sourced in the UK. We also make over
80% of our product range here at our factory.
NO HASSLE RETURNS
Change your mind or ordered the wrong size? Don’t worry, that’s cool. We’ll refund or swap it for you as long as it’s in new condition.
5 YEAR WARRANTY
We have been making cases since 1983 at our UK factory and we stand by the quality of our gear. Check our warranty terms at the bottom of the page.
FREE SHIPPING*
UK: for orders over £50 – under £50 fixed cost of £4
EU: orders over €60 – under €60 check your shopping cart for delivery costs.
Continental USA: orders over $50 – under $50 check your shopping cart for delivery costs